Pro-Line is proud to release the HD version of the Performance Transmission, which has been specifically designed to bring your 2wd Stampede® up to its full bashing potential with all steel internal gears. Every feature you would expect to find in a high-end race transmission has been combined with incredible durability and is now available for your Stampede®. This new HD Performance Transmission is also a great addition to your Electric Slash® 2WD, Electric Rustler® and Bandit®* and is a direct replacement for the Original Transmission that is included with the Pro-Line PRO-2 SC truck and PRO-2 Buggy and a stock replacement for the PRO-MT Monster Truck!
Pre-Assembled – Install and Go!
Transmissions are complicated and have a lot of moving parts. Pro-Line has done the work for you and pre-assembled the transmission to get you out and bashing faster! All you have to do is Install and Go! The Sealed, Oil-filled Differential has been pre-filled with 5,000 wt. diff oil and the slipper system has been pre-set for proper performance.
Sealed, Oil-Filled Gear Differential
The single biggest feature and upgrade over your stock transmission is Pro-Line’s Performance Differential. The design is based off of 1/8 Buggy style sealed differentials and is completely tunable to your current track conditions by changing the weight of the diff oil. The Differential features super smooth Steel Internal Diff Gears for the ultimate in durability and 4 O-Rings and a Diff Gasket that seals against fluid leakage. You will be amazed at how smooth the Differential is and how much it improves the performance of your vehicle.
Race Inspired Slipper System with Vented Discs
The Performance Transmission features a proven, race style Slipper Pad and plate system that is more consistent, lighter and runs truer than the stock slipper design. The Plates are Hard Anodized Aluminum with Vent Holes, which reduces heat and improves slipper consistency. Pro-Line’s 86T Spur Gear is extra wide for durability and is not offset like the stock spur gear. No more wobbly spur gears! The Clear hard plastic Gear Cover has a removable rubber cap for easy access to adjust the tension on the slipper system. Adjustments can be made with the same 7mm tool that you use to remove wheel nuts.
Heavy Duty Steel Gears
Pro-Line’s new Performance Transmission has been built to take some serious power with all steel internal gears. This allows for bigger motors, more powerful batteries and loads of wheelie popping fun! The Top Gear, Idler Gear, Bottom Gear and all of the internal Differential Gears are all made from strong Steel.
3mm Thick Aluminum Motor Plate, Full Ball Bearings, & Other Awesome Features
There are so many other awesome features that make Pro-Line’s Performance Transmission a must have. The motor mounts to 3mm thick Aluminum Motor Plate with cooling fins and a machined P-L logo, all of which act as a huge heat sink to keep your motor running cool. High quality Ball Bearings are used throughout the Transmission and the Differential spins on huge 10mm x 16mm x 5mm Ball Bearings for incredible load capability. The Toe Block is molded separate from the Transmission Case allowing for quicker and easier access to the Transmission when tuning the Differential Oil. The separate Toe Block also opens up the possibility for different tuning blocks (Toe Angle and Anti-Squat) to be used at some point in the future… The Hardened Steel Outdrive Shafts will accept the stock axles, as well as any aftermarket CVD’s or drive shafts that you might have for your vehicle.
Pro-Line’s Performance HD Transmission is the ultimate upgrade for your Slash® 2WD, Electric Stampede® 2WD, Electric Rustler® or Bandit®* and is the stock replacement for the Pro-Line PRO-2 SC, PRO-2 Buggy and PRO-MT trucks! No other company offers anything close to this type of performance upgrade for your Transmission, so be the first at your Bashing spot to streak past your friends with the help of your Pro-Line ProTrac, Power Stroke Shock and Transmission upgraded Stampede! Order your HD Performance Transmission Today!
*Bandit® requires use of a smaller pinion gear than what is included stock. Recommend an 18t or 19t pinion gear for most applications.
Do you want to add strength and style to your PRO-MT? Look no further than the PRO-MT Aluminum Rear Hub Carriers! These Gun Metal Anodized Aluminum Rear Hub Carriers are a direct fit for the Pro-Line PRO-MT and add extra stiffness to the rear of the Truck. Upgrade your PRO-MT today!
11/5/2014
Eng / Usd
Français
Deutsch
Italiano
Recent comments